Lock Picking

This article from wikiHow, with minor edits, explains how to pick a lock better than we ever could manage to do it alone. Keep in mind these instructions only apply to locks with no security pins. This encompasses around 50% of all locks in Australia. If you are ready to move on to more advanced locks including those with security pins consult our Guides section.

1. Understand how your lock works.

The pin-and-tumbler lock consists of a cylinder that can rotate within its housing (see the illustrations below). When locked, the cylinder is kept in place by several pairs of pins. The top pin of each pair protrudes into both the cylinder and the housing, thus preventing the cylinder from turning. When the correct key is inserted, it pushes the pairs of pins up so that the top pins no longer enter the cylinder. When this happens, the cylinder can be turned and the lock will open.

  • Note the five pairs of pins. The yellow pins enter both the cylinder and the silver housing around it. The springs provide resistance to keep the pins in place.
  • When the key is inserted, the grooves and ridges on the key push the pins up to the correct heights so that all the yellow pins are completely out of the cylinder, thus allowing the cylinder to turn and the lock to open.

2. Purchase a pick and tension wrench.

Each pick is specialized for a different problem. A tension wrench, or torque wrench, is the device you use to apply pressure to turn the lock cylinder. Professional-grade picks and tension wrenches can be purchased in sets (see picture), but many lock picking hobbyists make good quality sets of their own. See the Things You’ll Need section below for information on how to make your own picks and tension wrenches.

3. Place the tension wrench into the keyhole.

Place it anywhere that doesn’t block your pick’s from reaching the pins. Also place it so you are able to turn the lock cylinder with the tension wrench.

4. Determine which way the cylinder must be turned to unlock the lock.

If you commonly use the lock, you probably already know which way you turn the key to open the lock. If you don’t know, use the tension wrench to apply torque to the cylinder, first clockwise and then counter-clockwise. The cylinder will only turn a fraction of an inch before it stops. Try to feel the firmness of the stop. If you turn the cylinder the wrong way, the stop should feel very firm and stiff. If you turn it the right way, there should be a bit more give.

  • Some locks, especially among padlocks, will open regardless of which way the cylinder is turned.

5. Apply light torque to the tension wrench in the correct direction, and hold.

The required torque will vary from lock to lock and from pin to pin, so this may require some trial and error. Start gently, though.

6. Insert the pick into the upper part of the keyhole and feel the pins.

With the pick in the keyhole, you should be able to press up and feel the individual pins with the tip of the pick. You should be able to push them up and feel them spring back down when you release the pressure. Try to push each one all the way up. Identify which one is the hardest to push up. If they’re all very easy to push up, turn the tension wrench more to increase the torque. If one won’t go up at all, ease the torque until you can push it up. Alternatively, you may wish to “rake” the pins before this step (see Tips below).

7. Push the stubborn pin up until it “sets.”

Press the stubborn pin with just enough pressure to overcome the downward pressure of the spring. Remember, the pin is actually a pair of pins. Your pick is pushing against the lower pin, which in turn pushes against the upper pin. Your goal is to push the upper pin completely out of the cylinder. Then, when you stop pushing, the lower pin will fall back down into the cylinder, but the torque on the cylinder will result in a misalignment of the hole in the cylinder with the hole in the housing, and the upper pin should then rest on the cylinder without falling back down. You should hear a faint click as the upper pin falls back down on top of the cylinder. You should also be able to push the lower pin up a little with no resistance from the spring—when this occurs you most likely have the upper pin “set.”

8. Continue applying torque and repeat the last two steps for each of the remaining pins.

It is imperative that you maintain torque on the cylinder to prevent the set pins from dropping back down. You may need to make slight increases or decreases in torque for each pin.

9. Use the tension wrench to turn the cylinder and unlock the lock.

Once all the pins are set, you should be able to turn the cylinder. Hopefully you have already ascertained the correct direction to turn it. If you have chosen the wrong direction, you will need to start over and reset all the pins.

Article provided by wikiHow. Find author credits at the original wikiHow article on How to Pick a Lock. Content on wikiHow can be shared under a Creative Commons License.

12 thoughts on “Lock Picking

  1. Hi,

    I have a bolt/lock type I’m trying to open but having trouble finding a socket or key for it. Would you mind if I send you a picture of it in your reply back. I’m thinking a gator grip might work.


  2. When will the Single Lock Picks be available??

  3. If you ever need another source or resource for picking all different kinds of locks, feel free to use us a resource! That’s what we do 🙂

  4. Really well explained, can’t wait to try with my new tools. Looks like a whole heap of fun.

  5. I have just place an order with this company. The equipment and all the information supplied is phenomenal. I can’t wait to receive my items and start my new hobby.

  6. I need someone to unlock my door I left my key in my house

  7. Hi have been given a lockwood safe small have no code oor keys has 7 pin tubular lock
    Can u suppy me a tool to open please
    U were recommended as the best place to ask

  8. can you tell me what the australian laws are regarding owning lockpicking equipment as an amateur are please. or guide me to a site that explains it . thanks

    1. Hello,
      A ‘Things You’ll Need’ section was mentioned to learn how to make lockpicks and tension wrenches, but I couldn’t seem to find the section.
      Nevertheless, this was informative on how to pick a lock.

  9. Best explination ive seen for pick locks, completely understand it now, thanks

    1. yes

      i would agree, it certainly does help,
      especially with the little videos to show you what and how to do it.

  10. hi

    i am a student in year 8 at school and i have just had a bet with an enemy that
    i wouldn’t be able to pick/learn to pick a normal pad lock by the end of the week.
    this website was recommended to me by a sympathetic friend that said he used it too.

    could u guys help?

Leave a Reply